Vintage Fanes

[buggs]

I have been offered a pair of these.



They have been reconed. I have no idea if these are any good, worth $150 each, be a good match for a Hiwatt.

Comments and suggestions would be very welcome! Thanks

[OldSchoolDave]

Comments and suggestions would be very welcome!

Would be a good match for a Hiwatt IF the recone job is good. Can you get the cone codes from the seller? The stated price seems high in today's market, for a non-original cone. But, it's your call.

Dave

[buggs]

<dumbass question>What's a cone code?</dumbass question>

[OldSchoolDave]

<dumbass question>What's a cone code?</dumbass question>

Ink stamp or chalk marks on the back side of the cones, indicating part number (and, usually, manufacturer). They can look like this:

Cone_code_01.jpg (57.91 KiB) Viewed 3337 times

Reconed code reduced.jpg (170.03 KiB) Viewed 3337 times

Need to know what cones were used by the reconer. Some parts are better than others.

Dave

[buggs]

WHF5594 which is a Wharfdale recone kit

Does that pass muster?

[OldSchoolDave]

Does that pass muster?

It would in my book, although I'd still lobby for a more discounted price. But, that's just me .

Dave

[buggs]

OK. Then these are definatley an option.

My other thought is a new Fane AXA12 alnico paired with a new medusa 100.

Are you familiar with the new Fanes? New or old?

Thanks

[philmanatee]

I run the new Fanes in several cabs and am quite happy with them. I use the the Medusa 100's in the bottom cab of my live rig. My recording cab has two AXA 12's and two Medusa 150's in it. I've also got a bassman cab I loaded with two AXA !2's that sounds awesome, but I haven't played it as much as the Hiwatt cabs yet. Phil

[buggs]

Does the 150W medusa not overpower the AXA? Is the AXA an alnico or ceramic?

Thanks

[buggs]

Does that pass muster?

It would in my book, although I'd still lobby for a more discounted price. But, that's just me .

Dave

I may end up getting another recone due to the poor state of the solder tabs. Would weber be a good place to go for that?

[philmanatee]

Does the 150W medusa not overpower the AXA? Is the AXA an alnico or ceramic?

Thanks

The AXA's are alnico and seem to keep up nicely with the Medusa 150's. I talked to the dealer before I bought them and he assured me that it was a good combination that he uses. Phil

[buggs]

Does the 150W medusa not overpower the AXA? Is the AXA an alnico or ceramic?

Thanks

The AXA's are alnico and seem to keep up nicely with the Medusa 150's. I talked to the dealer before I bought them and he assured me that it was a good combination that he uses. Phil

I've seen the combination before, and looks good. That combo just went on ebay for $400. I was pretty tempted.

[OldSchoolDave]

I may end up getting another recone due to the poor state of the solder tabs. Would weber be a good place to go for that?

Not sure if they'll recone vintage Fanes. Drop 'em an email and ask ( http://www.tedweber.com/recone/ ).

And, let us know what they say!

Dave

[philmanatee]

Around the Sound in Seattle has reconed vintage Fanes for me before. Phil

[louis]

If you dont find nobody ,
I know a good place near Montreal called Belisle acoustics, http://tr.ca/

They've been reconing Fanes since the early 70's ,you can ask for Bruno at 450-691-2584



Louis