U.S. Members: Remember to VOTE TODAY!

Forum for pedal, guitar and off-topic discussions.

Moderator: Mods

Post Reply
User avatar
OldSchoolDave
Posts: 2060
Joined: Wed Nov 14, 2007 9:24 pm
Location: HP, NC USA
Contact:

U.S. Members: Remember to VOTE TODAY!

Post by OldSchoolDave »

We've done a great job of keeping politics off the Vintage Hiwatt discussion board - kudos to all.

Without endorsing any candidate, just a reminder for our U.S. members to GET OUT AND VOTE TODAY!

I'm OSD and I approved this message.

Dave
...Hey! I played that song when it was new...

http://www.OldSchoolDave.com
User avatar
mhuss
Site Admin
Posts: 1440
Joined: Thu Nov 15, 2007 5:40 am

Re: U.S. Members: Remember to VOTE TODAY!

Post by mhuss »

OldSchoolDave wrote:U.S. members to GET OUT AND VOTE TODAY!
+10000

--mark
User avatar
mikhailwatt
Posts: 858
Joined: Thu Nov 15, 2007 2:46 am
Location: Austin TX

Re: U.S. Members: Remember to VOTE TODAY!

Post by mikhailwatt »

For sure!

Unfortunately, residing in a Left-Coast blue state, my vote for president won't make a difference... but we have a very close race for governor, again. Hoping we get the right person for the job this time, especially if we are forced to fight against an anti-business/tax the "rich"/spread-the-wealth/cap & trade social#*%t" agenda at the Federal level. :evil:

Oops - did I just cross the line? I see that certain keywords turn into =spam=. :wink: :lol:
You can almost feel the current flowing
You can almost see the circuits blowing
User avatar
OldSchoolDave
Posts: 2060
Joined: Wed Nov 14, 2007 9:24 pm
Location: HP, NC USA
Contact:

Re: U.S. Members: Remember to VOTE TODAY!

Post by OldSchoolDave »

mikhailwatt wrote:Oops - did I just cross the line? :wink: :lol:
Yes. Now, sit in the corner and think about what you've done ;) .

Those who don't vote, don't have any right to complain for the next term. So, even if it's tilting at windmills.....VOTE!

Dave
mikhailwatt wrote:I see that certain keywords turn into =spam=.
Only a choice few. That one must be on some master list, of which I am not in control. We try to keep this forum as open as possible....until *someone* ruins it for everybody :evil: .
...Hey! I played that song when it was new...

http://www.OldSchoolDave.com
User avatar
mikhailwatt
Posts: 858
Joined: Thu Nov 15, 2007 2:46 am
Location: Austin TX

Re: U.S. Members: Remember to VOTE TODAY!

Post by mikhailwatt »

OldSchoolDave wrote:tilting at windmills
Heheheh... he said "windmills"... hehehe. Write in Townshend for Commissioner of Feedback. :lol:

Can I get a sticker that says "I Tilted"? :wink:
You can almost feel the current flowing
You can almost see the circuits blowing
User avatar
Dr.HI-TONE
Site Admin
Posts: 2675
Joined: Wed Nov 14, 2007 8:51 pm
Location: HIWATT Valley

Re: U.S. Members: Remember to VOTE TODAY!

Post by Dr.HI-TONE »

I voted.

Hoping for a miracle!

I may have to suceed and form my own HIWATT nation.
http://www.HI-TONE-Amps.com

HI-TONE, when only the best will do.

DR-F
User avatar
mikhailwatt
Posts: 858
Joined: Thu Nov 15, 2007 2:46 am
Location: Austin TX

Re: U.S. Members: Remember to VOTE TODAY!

Post by mikhailwatt »

Dr.HIWATT wrote:I may have to succeed and form my own HIWATT nation.
I hope you your secession is successful. :wink: Some of us might be interested in emigrating. :lol:
You can almost feel the current flowing
You can almost see the circuits blowing
User avatar
OldSchoolDave
Posts: 2060
Joined: Wed Nov 14, 2007 9:24 pm
Location: HP, NC USA
Contact:

Re: U.S. Members: Remember to VOTE TODAY!

Post by OldSchoolDave »

mikhailwatt wrote: Can I get a sticker that says "I Tilted"? :wink:
You can, but it'll disqualify you as a Pinball Wizard ;) .

Dave
...Hey! I played that song when it was new...

http://www.OldSchoolDave.com
User avatar
mikhailwatt
Posts: 858
Joined: Thu Nov 15, 2007 2:46 am
Location: Austin TX

Re: U.S. Members: Remember to VOTE TODAY!

Post by mikhailwatt »

OldSchoolDave wrote:You can, but it'll disqualify you as a Pinball Wizard ;) .
Guess I'll have to stick with Wii Bowling. :lol:
You can almost feel the current flowing
You can almost see the circuits blowing
Post Reply